waspsoft.com


Home > Backup Exec > Backup Exec Verify Error

Backup Exec Verify Error

Contents

The following services need to be running: SQL (Bkupexec) BE Remote Agent BE Device and Media BE Server Service BE Job Engine Service BE Agent Browser Oftentimes, you can force a I have worked down to 40 and the problem still occurs, although not on the original backup job that failed with this error. To keep the tangent going, I think this is just not a true statement.  Back 10 years ago when the best tapes out there for SMB's were DDS and other small I read you can't go the other way (newer version to older version). http://waspsoft.com/backup-exec/backup-exec-alert-media-error-the-backup-to-disk-device-is-offline.html

Simultaneous to the backup verification failing, we are getting errors in the system log, event id 11, source: Lsi_scsi, that say the driver detected a controller error on \Device\RaidPort1. The idea is simple: As data moves from one electronics module to another in the drive, each module checks the operation of the previous module to ensure that the data sent This worries me because the autoloader manual says the autoloader is not recommended for use with a RAID controller. Last night's backup was 100% successful because I turned off data verification.

Backup Exec Verify Taking Too Long

Just curious to get some other thoughts on that topic. No Yes Did this article save you the trouble of contacting technical support? Covered by US Patent. The SCSI bus timeout TechNote referenced below should be followed first to provide a possible resolution as it more specifically addresses the hardware setup and configuration.If all other troubleshooting has not

I wasn't given an ETA on that release only that it was coming. How low can I go?? Email Address (Optional) Your feedback has been submitted successfully! Backup Exec 2014 Verify Slow If not, you may have to manually associate the DLL file with Backup Exec.

If all or most of them are stop… Storage Software Disaster Recovery Windows Server 2008 Advertise Here 846 members asked questions and received personalized solutions in the past 7 days. Backup Exec Verify Slow Even more unusual is the fact that I have a very similar setup at another location with a TL2000 connected to a 2850 and a 39160 SCSI card with BE12 that For details, please refer to http://support.microsoft.com/kb/304101 The error refers to the instance of the file on the tape or backup to disk file. Configuration changes would include isolating a device on its own controller, reducing the total number of devices on the controller, or replacement of the hardware controller or tape device.  Terms of

We ran the Superloader on the previous backup server without any issues, running Backup Exec 10d on W2K3. Backup Exec 2012 Stuck On Verify Veritas does not guarantee the accuracy regarding the completeness of the translation. Go to Device settings c. Reply Subscribe RELATED TOPICS: Rant warning...

Backup Exec Verify Slow

Like a lot of others here I've never had a verify fail due to a tape/drive problem, but I'm also too superstitious to turn it off without a concrete reason. 0 It is a good idea to initially check for updates to the .NET Framework. Backup Exec Verify Taking Too Long You should also launch the Backup Exec Console and click on Tools | Backup Exec Services | Service Credentials | Change Service Account Information to ensure Backup Exec is configured to Backup Exec Verify Necessary that an LTO drives write process includes the write/verify process that you're then doing again with BE's verify.

well that and that I can never get 12.5's single item restore to NOT crash... his comment is here Right, GRT from disk because of how it backs the store up. Four data copy management misconceptions that affect your business What are some flat backup misconceptions? After getting a hold of NetApp again with the above information they have now told me this is a known issue and there is an internal bug report at NetApp for Backup Exec Verify Very Slow

  • My previous home was wired with Cat5E in almost every room.
  • To perform a single file restore without using DAR, set the value of the environment variable EXTRACT to e or E.
  • You should also try a new tape, in case the current tape is defective.
  • Please try the request again.
  • The adapter is single ended LVD Ultra 320, which is specifically stated in the scsi bus requirements of the superloader manual.
  • If the file referenced by the error does not exist on the system, the backup job log may display additional errors similar to the following: "Directory not found.
  • Showing recent items.
  • When we bought that house, it had an unfinished basement and an unfinished attic room, making the cabling process very simple.
  • Sorry, we couldn't post your feedback right now, please try again later.
  • Thank You!

I am trusting to 'smartverify' which I'd never heard of before. Reply Eric Schewe says: October 4, 2012 at 09:24 Thanks Sam! Is there a configuration that allows Backup Exec to address more memory? this contact form Article by: Alex Data center, now-a-days, is referred as the home of all the advanced technologies.

Well... Backup Exec Corrupt File Cannot Verify Uncheck the box for "Auto detect settings" If the above troubleshooting steps fail to resolve the issue, it is recommended to contact the hardware vendor and get the tape device(s) or hard This fix will be included in 7.3.7P1.

Create/Manage Case QUESTIONS?

We'll send you an email containing your password. Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password? The easiest way to correct this error is to remove and then reinstall the .NET Framework. Corrupt Data Encountered Backup Exec Help Desk » Inventory » Monitor » Community » ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection

I have worked out why the inventories were failing: even though Backup Exec detected the cleaning tape and put it into the 'cleaning' media set, I still had to set the You can pinpoint the problem service by opening the Service Control Manager and checking to see which service failed to start. Backup Exec may back up partial data from such a file, but when it is not able to continue the backup of the file, Backup Exec marks the file on the navigate here Instead, it performs a Cyclic Redundancy Check (CRC) verification of the data on the backup media.

Browse to the C:\Program Files\Symantec\Backup Exec folder. In the last week or so our backup has failed at the verify portion. I'm sorry I think I forgot to mention that previously. You may see this error reported as: Backup Exec agent install failed with error code 1603 Backup Exec remote agent failed 1603 This is one of the Backup Exec errors that

It is possible that updates have been made to the original version after this document was translated and published. Subscribe to our monthly newsletter for tech news and trends Membership How it Works Gigs Live Careers Plans and Pricing For Business Become an Expert Resource Center About Us Who We That might be your fix. New NetApp AFF, FAS arrays launch with ONTAP upgrade NetApp all-flash arrays and hybrid storage arrays get updates, along with the ONTAP operating system and added support for ...

No Yes How can we make this article more helpful? Like you I'm not as pressed since our Friday night Full job runs in to the weekend(and we're closed on the weekends). As with Backup Exec 2012, the Backup Exec button in the upper left corner. Please help! 0 Question by:lnqtechservices Facebook Twitter LinkedIn Google LVL 2 Best Solution byHoard Although not really an answer to your question...

Log onto the Backup Exec Central Administration Server. Select the bottom two choices to un-install/remove all SYMANTEC Drivers and delete entries for tape drives no longer available. Not all occurrences of Symantec Backup Exec error 1053 are related to the .NET framework. We would have transferred the old card to the new server but the Dell only has PCI-e slots.

Backup Exec seems to recognise the cleaning tape and assign it automatically to the 'cleaning media' media set. 0 LVL 2 Overall: Level 2 Server Hardware 2 Message Accepted Solution