waspsoft.com


Home > Error Code > Balboa Error Code Oh

Balboa Error Code Oh

Contents

If you have a bad circuit board, you'll know it. Water temperature has reached 118ºF. All started as usual. 2 hours later I noticed it had turned off and it was displaying a OH error. Make sure the pressure switch wire is connected to the proper circuit board connector. http://waspsoft.com/error-code/balboa-hl-error-code.html

drops. Email Address: Bath/Spa Professionals Homeowners Home | Contact Us | About Us | My Account | Shipping Policy | Return Policy | Privacy Policy | Terms & Conditions | Cannot Find There may be conditions that exist in which the spa control system will be unable to detect these conditions. Some Spa Brands or Models may have this Message Enabled, and the Interval between these Messages will be whatever the Spa Manufacturer has selected.

Balboa Sns Error Code

It appeared to be the sensor harness as that is what tripped the breaker. Do not enter the water. No action is necessary. Contact your Dealer or Service Organization.

There's roughly 2k ohm difference between the two Did they both go to 17.0? Why does the panel display "FLO" alternating with current temperature? Make sure that they are open. Balboa Vs500 Error Codes No action is necessary.

Cheers in advance Share this post Link to post Share on other sites countspacula 0 countspacula Members 0 129 posts Gender:Male Location:TN Interests:hot tub service Gender:Male Location:Columbia Interests:fixing hot tubs Balboa Error Codes Hot Tubs Spaminator provided by [OzzModz] Spaminator - vBulletin Mods & Addons Copyright © 2016 OzzModz Ltd. Why does the system power input fuse (20A, 25A or 30A) keep blowing? Steve Cape Coral, FL 2003 Jacuzzi Premium J350 w/ozonator & cover Reply With Quote 04-17-2012,06:27 PM #12 09lancer View Profile View Forum Posts View Articles Join Date Jun 2010 Posts

Category Howto & Style License Standard YouTube License Show more Show less Loading... Balboa Fault Codes Back to Top SAH or SANITIZER HIGH Message At the ORP Sensor, the "Sanitizer Level is High" (SAH).With an ORP Sensor Installed in the System, the Sanitizer Level is Above 830 If it's working properly, they'll be within a degree each other (until the heater is energized). The Spa or Hot Tub Panel Displays: :IC , iCE This indicates that the auxiliary sensor detects a possible freeze condition.

  1. Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way.
  2. In extremely hot weather, check for proper cabinet ventilation.
  3. All Rights Reserved.
  4. Press Any Button to Reset and Clear the Error Message.3.
  5. Is that a board?
  6. If a continuously running low-speed-only pump is only used for filtering (not for heating), that is not called a circ pump, but instead may be referred to as a "continuous filtration
  7. When I did get it to stay on (only twice) both pumps & the heater worked.
  8. Check for proper spa water level and ensure pump is primed.
  9. The Spa or Hot Tub Panel Displays: Cd, CLd This indicates that a sensor detects a possible freeze condition.
  10. Check the pressure switch wires for cuts.

Balboa Error Codes Hot Tubs

Spa Control Trouble-Shooting Why does the soldered in fuse located on the circuit board blow? Make sure the pump is primed and pumping properly. Balboa Sns Error Code Since I can't see down there, hopefully we don't have any mildew or mold growing in that area. Balboa Spa Error Codes No separate circa pump Does this sound plausible to any of you experts on here???

The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test. his comment is here Open the spa cover and let the spa cool down for 10 minutes, then touch the control panel to reset the circuits, or push a red reset button on air systems. SN = Non functional high temperature sensor. Press "Mode" Button to Clear Message. Balboa Vs501z Error Codes

I think it is a temp sensor. You Must Press Any Button to Reset when Water is below 108°F (42.2°C). Dirty Filter.5. http://waspsoft.com/error-code/balboa-error-code-sl.html Does it matter they are slightly different readings?

Heater is shut down, but other spa functions run normally. Balboa Hot Tub Heater Troubleshooting Press any "Cool", "Warm", or "Temp" Button to Exit Priming Mode.3. Where can I find your product manuals?

If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1.

dr = Inadequate water detected in heater. You may very well find the solutions you are looking for as well as new ideas that could come in handy later. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. Balboa Hot Tub Codes Make sure the pump is working properly and there's no air in the system, plugged filter, blocked jet, damaged impeller..etc The error should reset when the water (in the heater tube)

After about 45 Seconds, Check for Error Messages on the Topside Panel Display. If the hot tub operates normally, then recalibrate the pressure switch. When I turn it on... navigate here Loading...

If that fails, disconnect the Hi Limit and check it's continuity (closed=good). Thanks Share this post Link to post Share on other sites PreservedSwine 0 Spa Guru Members 0 1,381 posts Gender:Male Gender:Male Location:Fort Myers, Fl Posted April 30, 2012 · Report DO NOT remove the protective covers from any electrical enclosure, or attempt to service any related electrical device, unless you are a qualified electrician or service professional. Thanks again...

For spas without digital controls, you may need to manually reset the high limit switch near the heater housing. Low Water Flow (LF, FLO), is the usual cause of an overheating (OH, OHH) spa or hot tub. If it does and a new sensor set has been added, and still an OH, new board. The Spa or Hot Tub Panel Displays: dr, dry This indicates that there is not enough water in the heater.

OHS = Overheat. Heat Related Pump Not Running.8. Make sure that the water temperature displayed on the topside panel is at least 1 degree below the heater set temperature and set the control to standard mode. COL = Cool condition.

but it has to be just after resetting the breaker, usually twice. If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes Switch closed while pump is deactivated. Back to Top Snb, Sb, or SENSOR B SERVICE REQD Message "Sensor B" (Snb or Sb) is Not Operating Correctly.The Sensor Connected to the "Sens.B" Connector on the System Board may

I plugged everything in once again, without the sensor harness plugged in & the breaker tripped again. Spacare.com 888-772-9887 Technical Assistance 405-622-4950 0 Item(s) | Total: $0 Home Shop SpaCare.com Spa Part Index Circuit Board Repair Spa Covers Spa & Hot Tub Covers Spa Cover Lifts The spa obviously should not be used when OH or OHH is flashing on the topside control; as the water could be scalding hot for several more minutes. The Water Temperature will probably drop Below Set Temperature between Filter Cycles.

Recalibrate the pressure switch. I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address Too Many Closed Jets.6.