waspsoft.com


Home > Error Codes > Balboa Pack Error Codes

Balboa Pack Error Codes

Contents

Spa is shut down. Too Many Closed Jets.6. Remove the Spa Cover and allow Sanitizer to Dissipate, or do a Partial Water Change.Note: If you do Not have an ORP Sensor installed in the Spa System, you should Never dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). Check This Out

Email Address: Bath/Spa Professionals Homeowners Home | Contact Us | About Us | My Account | Shipping Policy | Return Policy | Privacy Policy | Terms & Conditions | Cannot Find The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. For more information regarding CTI tech support click here Blue Ridge Spa Side Error Codes (click here) Gatsby Spa Spa Side Error Codes (click here) Imperial Spa Spa Side Error Codes Press "Mode" Button to Clear Message.

Balboa Spa Error Codes

HL = High limit switch tripped. Spa has shut down. All Reminder Messages can be Disabled through the Topside Panel Users Menu.Note: The Balboa Default is to have this Message Disabled. On the subsequent power-ups, the GFCI test is skipped because the proper flag has been set in the software.Note: The GFCI Test Feature should only be Enabled in the United States

If there is Now an Error Message, select Message Other than PSt or Persist Fail below.No Error Messages3. If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below. Heater is shut down, but other spa functions run normally. Balboa Hot Tub Error Codes Sign in to make your opinion count.

If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. Balboa Vs501z Error Codes Back to Top rCA or CHANGE MINERAL CARTRIDGE Message Time to "Change Mineral Cartridge Reminder" (rCA)Install a New Mineral Cartridge per Manufacturers Instructions. You Must Press Any Button to Reset when Water is below 108°F (42.2°C). If there is No Error Message, Select "No Error Message" Below.

This Mode allows the User to Replace or Clean a Pressure Side Filter Cartridge without Equipment turning ON unexpectedly. Balboa Fault Codes DO NOT remove the protective covers from any electrical enclosure, or attempt to service any related electrical device, unless you are a qualified electrician or service professional. Do not use spa when temperature is flashing or the OH message is displayed. Sn2 = Nonfunctional temperature sensor.

Balboa Vs501z Error Codes

Chris 19,000 vinyl pool, solar heat, .75 hp tristar, 48 sq ft de filter Reply With Quote 02-03-2014,09:08 AM #2 Isaac-1 View Profile View Forum Posts View Articles Join Date It turns out it was the fuse in the control system. Balboa Spa Error Codes Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". Balboa Vs500 Error Codes Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Temperature is "Unknown" (- - - or - -) while in

Add pH Decreaser according to Manufacturers Instructions.Note: If you do Not have a pH Sensor installed in the Spa System, you should Never get this Message. his comment is here Back to Top SF or SAFETY FAULT Message There is a "Safety Fault" (SF) condition on a spa with a pump suction blockage switch.On a spa with a pump suction blockage Back to Top SnS or Sn Message SnS or Sn MessageIf the SnS or Sn Message is Alternating with the Water Temperature on the Display, it is a Possible Sensors Out ToE = Time out error. Balboa Spa Control Error Codes

  • Heat Related Pump Not Running.8.
  • Try Turning the Power OFF and back ON again, or Continue for a Detailed Test Procedure.1.
  • Too Many Closed Jets.6.
  • ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection to 0.0.0.10 failed.
  • Loading...
  • The Water Temperature is Always maintained within 1°F (.5°C) of Set Temperature.
  • Sign in Share More Report Need to report the video?

You can skip Priming Mode if you're restarting the spa for some other reason (without the water having been drained since the last time the spa functioned properly). SnS = Sensors out of balance. Check for proper spa water level and ensure pump is primed. this contact form Loading...

Low Water Level.2. Balboa Trouble Codes dr = Inadequate water detected in heater. Heater is deactivated.

All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 90 Days, but some Spa Brands or Models may be Different.

Add Sanitizer according to Manufacturers Instructions.Note: If you do Not have an ORP Sensor installed in the Spa System, you should Never get this Message. System will restart when temp. Also LMI metering chlorine dispenser pump and HotSpring Jetsetter I use and endorse TFtestKits TF-100 from http://tftestkits.net ~Remember TFP counts on your donations to keep this site ad free~ Reply With Balboa Spa Control Manual FLO = Flow Switch (heater is deactivated.

After about 45 Seconds, Check for Error Messages on the Topside Panel Display. We sell wholesale to businesses associated with the Pool / Spa and Water Industries only. 2013 H2OCompanyInc. The Sensors are Possibly Out of Sync with Each Other, or Not Indicating Close to the Same Temperature at Both Sensors. http://waspsoft.com/error-codes/bd2-error-codes.html FL2 = Pressure switch problem.

Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. Do not use spa when temperature is flashing or the OH message is displayed. Blocked Skimmer.4. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1.

This indicates a Possible Problem with the System Board. Dirty Filter.5. Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. The spa is at a temperature above 108° .

We invite you to please Register to create a new account. Heater disabled but the spa is operational. Closed Slice Valve.7. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 =

Press Any Button other than "Jets 1" to Exit Drain Mode and Standby Mode, and Return to Normal Operation. Check for clogged filter. COOL = Spa water is more than 20° F cooler than the temperature set point. Working...

Blocked Suction Fitting.3. If display shows only this message (blinking) spa is shut down. Press "Mode" Button to Clear Message. Contact your Dealer or Service Organization.

ToE = Time out error. Chris 19,000 vinyl pool, solar heat, .75 hp tristar, 48 sq ft de filter Reply With Quote « Previous Thread | Next Thread » Forum > Swimming Pool Care > Spas OH = High temperature condition, has reached 110°F. Other Heating Modes are Economy, Standard in Economy, and Sleep Modes.Note: On the Panels that Display the "Std" or "St" Messages, the Message will Only be Displayed for a Few Seconds